Wampler Brad Paisley: Paisley Drive Deluxe Pedal

sku# CPAISLEYDLX
Paisley Drive Pedal
Paisley Drive Pedal
  • Paisley Drive Pedal
  • Paisley Drive Pedal
  • Paisley Drive Pedal
 
  • Paisley Drive Pedal
  • Paisley Drive Pedal
  • Paisley Drive Pedal
$259.97
 
Brad Paisley's Tone, Your Tone
 
There's been a lot of demand for Wampler's long-since-discontinued Underdog overdrive pedal. And a lot of that demand comes from Brad Paisley. So to improve upon his already great-sounding Paisley Drive, Wampler provides you access to the Underdog's Nobels-like grit right alongside Brad's signature tone.
 
  • Channel 1 replicates the distinctive Underdog overdrive that continues to inspire Brad
  • Channel 2 is the same versatile, amp-like drive of the Paisley Drive
  • Each channel can be run independently or stacked in any order you choose
 
Signal Routing Versatility
 
To integrate with today's super-powerful pedal switchers and MIDI-based rigs, Wampler outfitted the Paisley Deluxe with the ability to route your signal to each channel individually. With a simple stomp of your programmed switcher, you're able to pull up either channel or a blend of both. It truly is like having two Brad Paisley-approved overdrive pedals in one box.        
 
  • Independent in and out jacks for each channel
  • Channels are individually selectable via pedal switchers
  • Can be run as two independent pedals or stacked either way 
 
Choosing “Stacked” vs. “Separate” Channel Switching
 
The toggle switch has 3 settings: 2>1, Separate, and 1>2.
 
Looking at the top of the pedal, the input jacks are on the right side (with an arrow pointing towards the knobs) and the output jacks are on the left side (with an arrow pointing away from the knobs). C1 means “channel 1” and C2 means “channel 2” on the jacks.
 
When in 2>1 mode and both channels are “on”, the guitar is routed into channel 2, then channel 1. The input cable from the guitar needs to be moved to the “C2” input jack, and the output cable to the amp needs to be moved to “C1” output jack. When in 1>2 mode and both channels are “on”, the guitar is routed into channel 1, then channel 2. The input cable from the guitar needs to be moved to the “C1” input jack and the output cable to the amp needs to be moved to the “C2” output jack. When the toggle is in the middle it is in “separate” mode, and the pedal can be used as two individual pedals, both with its respective input and output jack.
 
Please note that if the cables are not in the correct place, the toggle switch and effect will not work properly, but no damage is done.
 

Features

  • Built in the U.S.A
  • Battery connection and 9v power jack
  • Can run up to 18v (for more clean headroom)
  • High-grade components selected for their superior sound and response
  • Fat switch on Channel 1 gives the signal a slight gain boost along with more low-mid content giving a much fatter/fuller tone.
  • Full 3 band active EQ on Channel 1
  • Switchable stacking order (1 into 2, 2 into 1 or you can completely separate them)
  • Top-mounted jacks make pedalboard placement effortless

Power draw: 32.8 mA @ 9V, 39.8 mA @ 18V (LED will flash 3 times when power from battery is getting low) 

5” x 4.5” x 1.5″ (88.9mm x 114.3mm x 38.1mm) – height excludes knobs and switches 

Recommended Products
On-Stage Professional Single A-Frame Guitar Stand

$23.99

View Details

Planet Waves Pro-Winder String Winder

$17.20 $11.99

View Details